luma.core.error.DeviceNotFoundError:找不到SPI设备

Question

我正在尝试设置我的新点矩阵MCULED显示模块8x32与MAX7219在我的覆盆子PI3。在

我遵循了这里的所有步骤https://max7219.readthedocs.io/en/0.2.3/，当然也使用了他们建议的引脚。在

当我用午餐吃测试样本时：

sudo python examples/matrix_demo.py

然后我会得到一个永远不会启动样本测试的错误：

^{pr2}$

问题不是luma.core公司因为它存在：

luma.core                1.7.2     
luma.led-matrix          1.0.8

使用lsmod | grep -i spi命令，答案是：

spidev                  7373  0 
spi_bcm2835             7596  0 

命令ls -l /dev/spi*的答案是：

crw-rw---- 1 root spi 153, 0 Aug 29 17:17 /dev/spidev0.1

我还附上了find /sys/bus | grep spi的回复

/sys/bus/platform/devices/3f204000.spi
/sys/bus/platform/drivers/spi-bcm2835
/sys/bus/platform/drivers/spi-bcm2835/bind
/sys/bus/platform/drivers/spi-bcm2835/unbind
/sys/bus/platform/drivers/spi-bcm2835/module
/sys/bus/platform/drivers/spi-bcm2835/uevent
/sys/bus/platform/drivers/spi-bcm2835/3f204000.spi
/sys/bus/spi
/sys/bus/spi/drivers_probe
/sys/bus/spi/devices
/sys/bus/spi/devices/spi0.0
/sys/bus/spi/devices/spi0.1
/sys/bus/spi/uevent
/sys/bus/spi/drivers
/sys/bus/spi/drivers/spidev
/sys/bus/spi/drivers/spidev/bind
/sys/bus/spi/drivers/spidev/unbind
/sys/bus/spi/drivers/spidev/spi0.1
/sys/bus/spi/drivers/spidev/module
/sys/bus/spi/drivers/spidev/uevent
/sys/bus/spi/drivers/stmpe-spi
/sys/bus/spi/drivers/stmpe-spi/bind
/sys/bus/spi/drivers/stmpe-spi/unbind
/sys/bus/spi/drivers/stmpe-spi/uevent
/sys/bus/spi/drivers/fb_st7735r
/sys/bus/spi/drivers/fb_st7735r/spi0.0
/sys/bus/spi/drivers/fb_st7735r/bind
/sys/bus/spi/drivers/fb_st7735r/unbind
/sys/bus/spi/drivers/fb_st7735r/module
/sys/bus/spi/drivers/fb_st7735r/uevent
/sys/bus/spi/drivers_autoprobe

这是我的靴子/配置文件在

 For more options and information see
# http://rpf.io/configtxtreadme
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
dtparam=i2c1=on
#dtparam=i2s=on
dtparam=spi=on

# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on
enable_uart=1